Site Survey Tool - TamoGraph

Prev Page Next Page
System Requirements
Driver Installation
Licensing and Trial Version Limitations
Interface Overview
Access Point List
Floor Plan / Site Map
Plans and Surveys, Properties, and Options Panel
Main Menu
Performing a Site Survey
New Project Wizard
Data Collection
Understanding Survey Types: Passive, Active, and Predictive
Active Survey Configuration
Best Practices, Tips, and Tricks
Survey Job Splitting
Predictive Surveys
Drawing Walls and Other Obstructions
Drawing Attenuation Zones
Virtual APs Placement Methods
Manual Placing and Configuring Virtual APs
Automatic Placing and Configuring Virtual APs
Reconfiguring Virtual APs
Working with Presets
Applying Visualizations
Working with Multi-floor Sites
Mixing Real and Virtual Data
Best Practices, Tips, and Tricks
Analyzing Data – Passive and Predictive Surveys
Selecting Data for Analysis
Adjusting AP Locations After Passive Surveys
Splitting an AP into Multiple Unique APs
Working with Multi-SSID APs
Visualization Types
Signal Level
Signal-to-Noise Ratio
Signal-to-Interference Ratio
AP Coverage Areas
Number of APs
Expected PHY Rate
Frame Format
Channel Bandwidth
Channel Map
Analyzing Data – Active Surveys
Selecting Data for Analysis
Visualization Types
Actual PHY Rate
TCP Upstream and Downstream Rate
UDP Upstream and Downstream Rate
UDP Upstream and Downstream Loss
Round-trip Time
Associated AP
Spectrum Analysis
Hardware Requirements
Spectrum Data Graphs
Performing Spectrum Analysis Surveys
Viewing Collected Spectrum Data
Exporting Spectrum Data
Reporting and Printing
Customizing Reports
Google Earth Integration
Configuring TamoGraph
Plans and Surveys
Plan / Map
Client Capabilities
Colors and Value Ranges
AP Detection and Placement
Visualization Settings
Configuring GPS Receiver
Using GPS Configuration Dialog
Finding the GPS Receiver Port Number
Taking Photographs
Voice Control
Using TamoGraph in a Virtual Machine
Frequently Asked Questions
Sales and Support

Using TamoGraph in a Virtual Machine

You can install and use TamoGraph Site Survey inside a virtualized Windows OS running as a guest operating system on a Mac (or PC, if you prefer a virtual environment for whatever reason). In order to do that, you will need virtualization software, such as VMWare, Parallels Desktop for Mac, or Virtual Box.

Guest Operating System

As a guest Windows version, you can use Windows 10, Windows 8.1, Windows 8, or Windows 7, although we recommend Windows 10 or 8.1 for the reasons explained below.


To use TamoGraph for passive surveys, you need a compatible adapter. When you run our software on a Windows notebook, you can use any of the compatible adapters in different form factors. The list of compatible adapters can be found here. When you run TamoGraph inside a virtual Windows machine, you can use USB adapters only. Please refer to the adapter list to find the USB adapter you are going to use. We strongly recommend that you choose an adapter marked "Recommended." They are also always available from us directly when you buy the boxed version.

Virtualization Software Configuration

If your virtualization software supports USB 3.0 emulation (which is the case if you are using VMWare or Parallels Desktop for Mac), be sure to use USB 3.0 emulation rather than USB 2.0 emulation, even if the USB port and the Wi-Fi adapter you are going to use are USB 2.0. Support for USB 3.0 requires Windows 8 or higher as the guest OS. USB configuration in VMWare is illustrated below.


USB 3.0 emulation is preferable because it dramatically increases the communication speed between the Wi-Fi adapter and guest OS. For example, in some adapters, switching the Wi-Fi channel might take 500 or even 1,000 milliseconds if you use USB 2.0 emulation and only 100 milliseconds if you use USB 3.0 emulation. Considering the fact that TamoGraph typically switches channels every 250 milliseconds, this difference is dramatic. Using USB 2.0 emulation might slow down the application considerably.

For this reason, we recommend that you do not use VirtualBox as virtualization software. At the time of writing, VirtualBox has no USB 3.0 support. If you still want to use VirtualBox, at least use the Enable USB 2.0 (EHCI) Controller option; otherwise, your USB Wi-Fi adapter might not work.

Adapter Installation

Plug in the USB adapter into your computer. Once the adapter is plugged in, you will need to configure your virtualization software to use the detected USB device, i.e. disconnect it from the host OS and connect it to the guest OS.  The configuration method depends on the specific virtualization software that you use; please refer to the related documentation. After the virtual machine takes control of the adapter, Windows will notify you that a new USB device has been found and will try to find the driver for the device. Click Help => Driver Installation Guide in TamoGraph to find the instructions for installing our special packet capture driver. Once that driver has been installed, you can restart the application and use it.